Faculty Bibliography

BACKGROUND:Non-cruciate total knee arthroplasty designs, including ultracongruent, medially congruent, and medial pivot, are gaining increasing attention in total knee arthroplasty surgery. However there is no consensus for the bearing surface design, whether there should be different medial, lateral, anterior and posterior laxities, or whether the medial side should be a medial pivot. This study proposes the criterion of reproducing the laxity of the anatomic knee, defined as the displacements and rotations of the femur on the tibia in the loaded knee when shear and torque are applied. The purpose of this study was to determine the ideal tibial radii to achieve that goal. METHODS:The femoral component was based on the average knee from 100 mild arthritic knee scans. There were eight tibial components that were designed with different sagittal radii: antero-medial, antero-lateral, postero-medial, and postero-lateral. Radii were defined as the percent height reduction from full conformity with the femoral profile. Components were 3D printed. A test rig was constructed where the tibial component was fixed and shear and torque were applied to the femoral component. Displacements and rotations of the femoral component were measured at 0 and 45 degrees of flexion, the latter representing any flexion angle due to the constant femoral sagittal radius. RESULTS:Displacements ranged from 0 to 11mm, and rotations ranged from 1 to 11 degrees. Anterior femoral displacements were higher than posterior due to the shallow distal-anterior femoral profile. The final femoral and tibial components with the most closely matched anatomic laxity values, were designed and tested. CONCLUSIONS:A steeper distal-anterior femoral radius was an advantage. High medial-anterior tibial conformity was important. However, on the lateral side, the posterior sagittal tibial radius had to be shallower than ideal to allow femoral rollback in high flexion. This meant that the posterior laxity displacements on the lateral side were higher than anatomic, and there was no guidance for lateral femoral rollback.

PURPOSE/OBJECTIVE:Soft tissue balancing is an important step in a total knee procedure, carried out manually, or using an indicator. The purpose of this study was to evaluate our design of 3D printed Balancer, and demonstrate how it could be used at surgery. PROCEDURES/METHODS:When inserted between the femur and tibia, the Balancer displayed the forces acting across the lateral and medial compartments, indicated by pointers at the end of the handle. A loading rig was used to measure the pointer deflections for different forces applied at different locations on the condyle surfaces. Repeatability and reproducibilty were evaluated. The Balancer was tested in six fresh knee specimens using a surgical simulation rig. MAIN FINDINGS/RESULTS:Pointer deflections of up to 12 millimeters occurred for less than 1 mm displacements at the condyle surfaces. Reproducibility tests showed a standard deviation of 14% at lower loads, reducing to only 4% at higher loads. Mean pointer deflections were within 8% for forces applied at ±10 mm AP, and +5/-3 mm in an ML direction, relative to the neutral contact point. In specimens, most lateral to medial force differences could be corrected by a 2° change in frontal plane angle of the tibial resection. Effects of ligament releases were also demonstrated. PRINCIPAL CONCLUSIONS/CONCLUSIONS:The 3D printed Balancer was easy to use, and provided the surgeon with lateral and medial force data over a full range of flexion, enabling possible corrective procedures to be specified.

BACKGROUND:Since the introduction of the first total knee designs, a frequent design goal has been to reproduce normal knee motion. However, studies of many currently used total knee designs, have shown that this goal has not been achieved. We proposed that Guided Motion total knee designs, could achieve more anatomic motion than present standard designs. METHODS:Several Guided Motion knees for application without cruciate ligaments were designed using a computer method where the bearing surfaces were generated by the motion required. A knee testing machine was constructed where physiological forces including compressive, shear and torque were applied during knee flexion. The neutral path of motion and the laxity about the neutral path were measured. This evaluation method was a modification of the ASTM standard Constraint Test. RESULTS:The motions of the Guided Motion knees and a standard PS knee were compared with the anatomic motion of knee specimens determined in an earlier study The Guided Motion knees showed motion patterns which were closer to anatomic than the PS knee. CONCLUSIONS:The results provided justification for carrying out further evaluations of functional conditions, using either knee simulators or computer modelling. If anatomic motions could be reproduced in vivo, it is possible that clinical outcomes could be improved.

Obtaining anatomic knee kinematics after a total knee is likely to improve outcomes. We used a crouching machine to compare the kinematics of standard condylar designs with guided motion designs. The standard condylars included femoral sagittal radii with constant radius, J-curve and G-curve; the tibial surfaces were of low and high constraint. The guided motion designs were a medial pivot and a design with asymmetric condylar shapes and guiding surfaces. The machine had a flexion range from 0° to 125°, applied quadriceps and hamstring loading, and simulated the collateral soft tissues. The kinematics of all standard condylar knees were similar, showing only small anterior-posterior displacements and internal-external rotations. The two asymmetric designs showed posterior displacements during flexion, but less axial rotations than anatomic knees. The quadriceps forces throughout flexion were very similar between all designs, reflecting similar lever arms. It was concluded that standard condylar designs, even with variations in sagittal radii, are unlikely to reproduce anatomic kinematics. On the other hand, designs with asymmetric constraint between medial and lateral sides, and other guiding features, are likely to be the way forward. The mechanical testing method could be further improved by superimposing shear forces and torques during the flexion-extension motion, to include more stressful in vivo functional conditions.

BACKGROUND:To measure functional outcome, patient reported outcome measures (PROMs) are most often used but biomechanical tests can provide valuable supplementary data. The objective of this study was to investigate instrumented insoles for measuring ground-to-foot forces during basic activities. METHODS:Three groups were evaluated: normal controls, preoperative, and postoperative total knees. The Knee Society Scoring System (KSS) Short Form was used, and with foot pressure sensor insoles, a timed-up-and-go (TUG) test and a sit-to-stand (STS) test was used. RESULTS:Comparing preoperative to postoperative and control groups, there were significant differences in most parameters. There were no significant differences between controls and postoperative knees. Of the 33 correlation coefficients between three PROM parameters and six biomechanical parameters for the three groups, only five coefficients were greater than 0.5. CONCLUSIONS:The biomechanical data was substantially independent of the PROM data and provided additional functional evaluation. The most useful parameters were the left-right force ratios during sit-to stand (STS) and the timed-up-and-go (TUG) time.

Implant alignment and soft-tissue balancing are important factors in total knee arthroplasty (TKA). The purpose of this study was to design a mechanical balancing device, which measures deflections resulting from forces applied on each condyle to provide numerical data indicating the extent of ligament release needed, or angular changes in the bone cuts required to achieve a balanced knee. Two mechanical devices were designed and 3D printed, Pistol Grip and In-line. The Pistol Grip design consisted of a lever system that indicated the difference between lateral and medial forces with a single pointer. The In-line design allows for the quantification of the absolute force applied on each individual condyle. The two designs were evaluated on a test rig designed to model balance and imbalance conditions in the knee. For the Pistol Grip design maximum pointer deflection indicates a 2 mm change in elevation per condyle and/or a 3 degrees angular change of the condyles which can be corrected by adjusting the ligament lengths equivalent to 2 mm and/or by modifying the proximal or distal femur bone cut by 3 degrees. For the In-line design, maximum pointer deflection represented a 40 N load on the condyle. Our mechanical balancer designs were successful in providing information that can guide surgeons to accurately achieve balance through ligamentous releases and/or modification to bone cuts. The balancer designs are easy to use, do not require any electronics or software, and can be incorporated into the surgical procedure.

Limb alignment is a critically important factor to consider in the management of the patient with knee arthritis. Abnormal alignment is associated with the accelerated progression of osteoarthritis and, if not addressed at the time of surgery, may contribute to early failure of knee replacement implants. The contribution of the hindfoot to overall limb alignment has received limited attention in the context of deformity correction in total knee arthroplasty (TKA). In this review, we present evidence supporting the inclusion of the hindfoot in the consideration of overall limb alignment for TKA and propose a management algorithm.

AIMS/OBJECTIVE:This aim of this study was to assess the feasibility of designing and introducing generic 3D-printed instrumentation for routine use in total knee arthroplasty. MATERIALS AND METHODS/METHODS:Instruments were designed to take advantage of 3D-printing technology, particularly ensuring that all parts were pre-assembled, to theoretically reduce the time and skill required during surgery. Concerning functionality, ranges of resection angle and distance were restricted within a safe zone, while accommodating either mechanical or anatomical alignment goals. To identify the most suitable biocompatible materials, typical instrument shapes and mating parts, such as dovetails and screws, were designed and produced. RESULTS:Before and after steam sterilization, dimensional analysis showed that acrylonitrile butadiene styrene could not withstand the temperatures without dimensional changes. Oscillating saw tests with slotted cutting blocks produced debris, fractures, or further dimensional changes in the shape of Nylon-12 and polymethylmethacrylate (MED610), but polyetherimide ULTEM 1010 was least affected. CONCLUSION/CONCLUSIONS:2019;101-B(7 Supple C):115-120.

BACKGROUND:Spacer blocks, tensors, or instrumented tibial trials are current methods of balancing the knee during surgery but there are no current techniques for measuring ligament forces. Our goal was to study the relationship between the collateral ligament forces and the condylar contact forces to determine whether there was equivalence. METHODS:A test rig was constructed modeling an artificial knee joint with collateral ligaments. The ligament forces as well as the lateral and medial tibial contact forces were measured during flexion for different positions of the femoral component on the femur, producing a set of forces for the simulated conditions. A regression analysis was used to study the correlation between the ligament and contact forces. RESULTS:The combined medial and lateral ligament and contact forces showed a linear relation with a correlation coefficient of 0.98. For the medial and lateral sides separately, the correlations were 0.85 and 0.88, respectively, with more than 80% of points within a ±25% deviation from the linear relations. This deviation from the linear correlation is linked to differences in medial-lateral femoral-tibial contact point locations at different flexion angles. CONCLUSION/CONCLUSIONS:Within balancing accuracies generally achieved at surgery, the collateral ligament forces were linearly correlated to the condylar contact forces. These forces can also be equally correlated to the distraction forces as well as the moments at which condylar liftoff would occur from varus-valgus moments. This indicated a unification of the different balancing parameters, and hence such quantitative methods can be used interchangeably.

Background/UNASSIGNED:The purpose of the study was to investigate the accuracy of balancing which could be achieved at total knee surgery and its relation to functional outcomes. Methods/UNASSIGNED:During surgery, the forces on the medial and lateral plateaus were measured at 10-15 degrees flexion in 101 patients, using an instrumented tibial trial, with equal forces being targeted. Of the initial 101 cases, 71 cases completed all follow-up visits to 1 year. At each follow-up visit, the function was measured using the Knee Society Scoring System, and varus and valgus laxity angles were measured. Results/UNASSIGNED:The mean medial/(medial + lateral) compartmental force ratio was 0.52, with a standard deviation of 0.09. The total contact force was 217 Newtons, with a standard deviation of 72 Newtons. No correlations were found between the functional scores and the compartmental force ratio or total contact force. However, the mean varus and valgus laxity angles, 2.8 and 2.3 degrees, respectively, were very close to the angles of normal intact knees. Conclusions/UNASSIGNED:The likely reason for the lack of correlation of function was that the large majority of the balancing ratios were within the range 0.4-0.6 but with a wide spread of functional scores typical of total knee study groups. However, the normal varus and valgus angles achieved at follow-up indicated that equal balancing in early flexion was a reasonable surgical target. Using instrumented tibial trials enabled accurate and consistent balancing values to be achieved, as well as normal varus and valgus laxity angles, which may be important in obtaining optimal outcomes.