Faculty Bibliography

OBJECTIVES/OBJECTIVE:To evaluate the three-dimensional fit of abutments fabricated by the industry to those either milled or cast by a commercial laboratory and to correlate the implant-abutment connection fit with stress at fatigue failure of prostheses. Probability of survival (reliability) and fractography to characterize failure modes were also performed for cemented and screw-retained prostheses. METHODS:One-hundred and twenty-six maxillary central incisor crowns were milled to restore implants and divided in 3 cemented and 3 screwed-retained groups (n = 21/each), as follows: [Digital-Sc]: milled one-piece monolithic abutment/crown; [TiB-Sc]: milled crowns cemented onto Ti-base abutments; [UCLA]: screw-retained crown using UCLA abutments; [Digital-Ce]: milled two-piece assembly comprised by screwed monolithic abutment and a cemented crown; [TiB-Ce]: milled coping cemented onto Ti-base abutments to receive a cemented crown; [UCLA-Ce]: UCLA abutments that received an overcast coping and a cemented crown. Implant-abutment volume misfit was assessed by micro-computed tomography using the silicone replica technique. Implant/crown systems were subjected to step-stress accelerated life testing (SSALT) in water. The use-level probability Weibull curves and reliability for a mission of 50,000 cycles at calculated stress at failure of 2,300, 3300 and 4300 MPa were plotted. Fractographic analysis was performed with scanning electron microscopy. Internal misfit was analyzed through one-way ANOVA following post-hoc comparisons by Tukey test (p < 0.05). Correlation between misfit volume and the stress at fatigue failure was assessed by Pearson test. RESULTS:). The mean β values were: 1.68, 1.39, 1.48, 2.41, 2.27 and 0.71 for Digital-Sc, TiB-Sc, UCLA, Digital-Ce, TiB-Ce and UCLA-Ce, respectively, indicating that fatigue was an accelerating factor for failure of all groups. Higher stress at failure decreased the reliability of all groups, more significantly for screw compared to cement-retained groups, especially for Digital-Sc that demonstrated the lowest reliability. The failure mode was restricted to abutment screw fracture. A negative correlation was observed between misfit values and stress at failure (r = -0.302, p = 0.01). CONCLUSIONS:Abutments milled by a commercial lab presented higher misfit compared to those provided by the industry and a moderate correlation was observed between higher misfit and lower stress at failure during fatigue. Probability of survival decreased at higher stress, especially for screw compared to cement-retained groups, and failures were confined to abutment screws.

This study investigates a comprehensive model of bone regeneration capacity of dypiridamole-loaded 3D-printed bioceramic (DIPY-3DPBC) scaffolds composed of 100% beta-tricalcium phosphate (β -TCP) in an immature rabbit model through the time of facial maturity. The efficacy of this construct was compared to autologous bone graft, the clinical standard of care in pediatric craniofacial reconstruction, with attention paid to volume of regenerated bone by 3D reconstruction, histologic and mechanical properties of regenerated bone, and long-term safety regarding potential craniofacial growth restriction. Additionally, long-term degradation of scaffold constructs was evaluated. At 24 weeks in vivo, DIPY-3DPBC scaffolds demonstrated volumetrically significant osteogenic regeneration of calvarial and alveolar defects comparable to autogenous bone graft with favorable biodegradation of the bioactive ceramic component in vivo. Characterization of regenerated bone reveals osteogenesis of organized, vascularized bone with histologic and mechanical characteristics comparable to native bone. Radiographic and histologic analyses were consistent with patent craniofacial sutures. Lastly, through application of 3D morphometric facial surface analysis, our results support that DIPY-3DPBC scaffolds do not cause premature closure of sutures and preserve normal craniofacial growth. Based on this novel evaluation model, this DIPY-3DPBC scaffold strategy is a promising candidate as a safe, efficacious pediatric bone tissue engineering strategy.

BACKGROUND:Surgical fixation of implants into bone for the correction of bone deformities or defects is a traditional approach for skeletal stabilization. Important measures of efficacy of implants include implant stability and osseointegration-the direct interaction between living bone and an implant. Osseointegration depends on successful implant placement and subsequent bone remodeling. This study utilized osseodensification drilling (OD) in a low bone density model using trabecular metal (TM) implants. MATERIAL AND METHODS/METHODS:Three osteotomy sites, Regular, OD-CW (clockwise), and OD-CCW (counterclockwise), were prepared in each ilium of three female sheep. Drilling was performed at 1100rpm with saline irrigation. Trabecular metal (TM) (Zimmer, Parsippany, NJ, USA) implants measuring 3.7mm in diameter x 10mm length were placed into respective osteotomies. A three-week period post-surgery was given to allow for healing to take place after which all three sheep were euthanized and the ilia were collected. Samples were prepared, qualitatively and quantitatively analyzed using histology micrographs and image analysis software (ImageJ, NIH, Bethesda, MD). Bone-to-implant contact (BIC) and bone area fraction occupancy (BAFO) were quantified to evaluate the osseointegration parameters. RESULTS:All implants exhibit successful bone formation in the peri-implant environment as well as within the open spaces of the trabecular network. Osseointegration within the TM (quantified by %BIC) as a function of drilling technique was more pronounced in OD samples(p>0.05). The %BAFO however shows a significant difference (p=0.036) between the CCW and R samples. Greater bone volume and frequency of bone chips are observed in OD samples. CONCLUSION/CONCLUSIONS:The utilization of OD as a design for improved fixation of hardware was supported by increased levels of stability, both primary and secondary. Histological data with OD provided notably different results from those of the regular drilling method.

Recombinant human bone morphogenetic protein-2 (rhBMP-2) is one of the most commonly used osteogenic agents in the craniofacial skeleton. This study reviews the safety and efficacy of rhBMP-2 as applied to craniofacial reconstruction and assesses the level of scientific evidence currently available.

Treatment of large bone defects is a challenging clinical situation that may be benefited from cell therapies based on regenerative medicine. This study was conducted to evaluate the effect of local injection of bone marrow-derived mesenchymal stromal cells (BM-MSCs) or adipose tissue-derived MSCs (AT-MSCs) on the regeneration of rat calvarial defects. BM-MSCs and AT-MSCs were characterized based on their expression of specific surface markers; cell viability was evaluated after injection with a 21-G needle. Defects measuring 5 mm that were created in rat calvaria were injected with BM-MSCs, AT-MSCs, or vehicle-phosphate-buffered saline (Control) 2 weeks post-defect creation. Cells were tracked by bioluminescence, and 4 weeks post-injection, the newly formed bone was evaluated by µCT, histology, nanoindentation, and gene expression of bone markers. BM-MSCs and AT-MSCs exhibited the characteristics of MSCs and maintained their viability after passing through the 21-G needle. Injection of both BM-MSCs and AT-MSCs resulted in increased bone formation compared to that in Control and with similar mechanical properties as those of native bone. The expression of genes associated with bone formation was higher in the newly formed bone induced by BM-MSCs, whereas the expression of genes involved in bone resorption was higher in the AT-MSC group. Cell therapy based on local injection of BM-MSCs or AT-MSCs is effective in delivering cells that induced a significant improvement in bone healing. Despite differences observed in molecular cues between BM-MSCs and AT-MSCs, both cells had the ability to induce bone tissue formation at comparable amounts and properties. These results may drive new cell therapy approaches toward complete bone regeneration.

New resin-based restorative materials have been developed, such as computer-aided design/computer-aided manufacturing (CAD/CAM) and bulk-fill composites, as an alternative to traditional layering techniques. This study evaluated the biaxial flexural strength (BFS) before and after thermocycling of five different resin composites: one hybrid resin/ceramic CAD/CAM indirect material, Lava Ultimate CAD-CAM Restorative (LU, 3M Oral Care); a conventional composite, Filtek Z350 XT (Z350, 3M Oral Care); two bulk-fill composites, Tetric N-Ceram Bulk Fill (TBF, Ivoclar Vivadent) and Filtek Bulk Fill (FBF, 3M Oral Care); and one bulk-fill flow resin composite, Filtek Bulk Fill Flow (FBFF, 3M Oral Care). Three hundred disc-shaped specimens (6.5 mm in diameter and 0.5 mm thick) were fabricated and divided into five groups (n=30 for each composite and condition). The BFS test was performed in a universal testing machine at a crosshead speed of 0.5 mm/min immediately (i, 24 hours) and after thermocycling (a, 500 thermal cycles of 5°C to 55°C with a 30-second dwell time). The Weibull modulus (m) and characteristic stress (η) were calculated, and a contour plot was used (m vs η) to detect differences between groups (95% two-sided confidence intervals). Significantly higher characteristic stress was observed for LUi (286.6 MPa) and Z350i (248.8 MPa) compared to the bulk-fill groups (FBFi=187.9 MPa, FBFFi=175.9 MPa, TBFi=149.9 MPa), with no differences between LUi and Z350i. Thermocycling significantly decreased the characteristic stress of all groups with the highest values observed for LUa (186.7 MPa) and Z350a (188.9 MPa) and the lowest for FBFFa (90.3 MPa). Intermediate values were observed for FBFa (151.6 MPa) and TBFa (122.8 MPa). The Weibull modulus decreased only for FBFa compared to FBFi. Composition and thermocycling significantly influenced the biaxial flexural strength of resin composite materials.

Background/Purpose: Previous in vivo and in vitro animal studies demonstrate that the adenosine A2A receptor (A2AR) agonist dipyridamole (DIPY) stimulates robust osteogenic differentiation and proliferation without adverse effects on craniofacial suture development. However, no studies to date have been performed on human tissue. This study compares the effects of DIPY, BMP-2, and standard osteogenic media on osteogenic differentiation by human mesenchymal stem cells to lay the foundation for translating this bone tissue engineering approach to pediatric craniofacial reconstruction. Methods/Description: Pediatric mesenchymal stem cells were isolated from surplus bone taken from consented patients undergoing craniofacial surgery. Cells were cultured at early passage for 3 weeks in 1 of 7 experimental conditions: control media; osteogenic media (control + 100 muM beta-glycerophosphate, 0.1 muM dexamethasone and 100 mg/ mL L-ascorbic acid); osteogenic media + 200 ng/mL BMP-2; osteogenic media + 10, 100, 1000, or 10 000 muM DIPY. All experiments were performed in biological triplicates. Samples were analyzed using Alkaline phosphatase (ALP) assay at 6 hours, 24 hours, 48 hours, and 7 days as a marker of early osteogenic differentiation. At the end of the 3-week differentiation period, cells underwent immunocytochemistry to verify phalloidin, osteocalcin, and collagen I expression. Alizarin red staining was used to detect mineralization. Statistical analysis used 1-way ANOVA with Tukeys post hoc correction and multiple t test comparison of means.
Result(s): In all osteogenic conditions, relative peak ALP activity occurred at 48 hours. One thousand micrometer DIPY showed significantly increased peak ALP activity compared to BMP-2 (3.6 +/- 0.1 fold increase vs 3.1 +/- 0.1; P = .006). There was no significant difference between 1000 muM DIPY and osteogenic media (4.1 +/- 0.1; P = .36). At 3 weeks, immunocytochemistry revealed differentiation in all osteogenic conditions compared to control. One thousand micrometer DIPY cells showed greater evidence of mature osteogenic differentiation including cuboidal cell morphology and deposition of collagen I in an extracellular fibrillar network pattern compared to both control osteogenic media and BMP-2. Alizarin red quantification demonstrated significantly increased extracellular matrix mineralization at 100 muM(2.4+/-0.4; P = .002), 1000 muM (4.3+/-0.6; P = .001), and 10 000 muM (5.1 +/- 0.2; P < .0001) DIPY compared to nonosteogenic control medium (1.0 +/- 0.1). Matrix mineralization was not significantly different between BMP-2 (2.4 +/- 0.2) and 1000 muM DIPY (P = .08). ImageJ analysis revealed increased proportion of osteocalcin expressing cells (40.0% +/- 2.8%) in stem cells treated with 1000 muM of dipyridamole compared to control (1.0% +/- 0.6%), osteogenic (5.8% +/- 1.0%), and BMP-2 (16.9% +/- 2.2%; P < .0001).
Conclusion(s): Dipyridamole promotes early osteogenic differentiation and maturation of human bone-derived mesenchymal stem cells. These data suggest that dipyridamole may be an effective tissue engineering strategy for pediatric craniofacial reconstruction

Background/Purpose: Alveolar cleft surgery is the most common bone reconstruction performed in patients with a cleft. Osteogenic agents such as BMP-2 have been used to restore the bony cleft without the morbidity of bone graft, but concerns remain regarding premature fusion of sutures, exuberant bone formation, and malignant degeneration. We have recently demonstrated that dipyridamole-coated, 3D printed bio-ceramic (3DPBC) scaffolds generate comparable bone amounts to BMP2 and significantly greater bone compared to negative controls in short-term growing animal model studies. No detrimental effects to growth sutures were noted in any animals. This study investigates the long-term osteogenic properties, degradation kinetics, and effects on facial growth of these tissue engineering constructs in growing animal models. Methods/Description: Twenty-two 1-month-old (immature) New Zealand white rabbits underwent creation of unilateral 3.5 x 3.5 mm alveolar defects. Each alveolar defect was repaired with either 3DPBC scaffolds coated with 1000 muM dipyridamole (n = 14) or with autogenous bone graft from the radius (n = 8). Six rabbits from the 3DPBC scaffold group were sacrificed at 8 weeks. The remaining rabbits (n = 8 each group) were euthanized following completion of craniofacial growth (6 months). Bone regeneration, scaffold degradation, and maxillary suture patency were calculated using CT images reconstructed and analyzed in Amira software. Facial symmetry was evaluated using dense-surface 3D modeling and validated with bilateral cephalometric measurements of maxillary projection. Bone growth and suture patency were qualitatively evaluated through histologic analysis.
Result(s): After 6 months, animals with defects repaired with 3DPBC scaffolds regenerated an average of 52.9% +/- 3.3% bone (mean +/- SEM), compared to 40.7%+/-4.0% in defects repaired with bone graft (P = .02). This is compared to unoperated alveolus occupied by 39.3% +/- 1.6% bone. Scaffolds showed significant degradation at 6 months (6.7% +/- 1.6%) compared to at 8 weeks (27.1% +/- 1.9%; P >= .001). Morphometric analysis using dense surface modeling showed similar symmetry indices of 55.0 +/- 3.3 for scaffold animals and 61.7% +/- 1.6% for bone graft animals (P = .10). Comparative measurements of operated and unoperated sides showed no significant differences in asymmetry between scaffold and bone graft animals (P = .86). Histologic analysis of scaffold samples revealed vascularized, organized bone within scaffold interstices without evidence of ectopic bone, excess inflammatory cells, or suture fusion.
Conclusion(s): In a growing animal model, dipyridamole-coated 3DPBC scaffolds can regenerate bone comparable to autogenous bone graft by radiographic and histologic analysis. Over 6 months, scaffolds show significant, favorable degradation and do not result in premature suture fusion or disruption of facial growth compared to bone graft. These results support long-term safety and efficacy of this tissue engineering strategy in the repair of alveolar cleft defects

Background/Purpose: Our tissue engineering laboratory has previously demonstrated that dipyridamole-coated, 3D printed bioceramic (3DPBC) scaffolds comprised of B-tricalcium phosphate generate significantly more bone compared to negative controls in short-term growing animal model studies. No detrimental effects to the cranial suture were observed in any experimental animals. The longterm osteogenic efficacy and safety of our 3DPBC scaffold for tissue engineering in growing calvaria was assessed by describing bone regeneration compared to autogenous bone graft, scaffold degradation kinetics, and the effects of the construct on cranial growth over time. Methods/Description: Twenty-two 1-month-old (immature) New Zealand white rabbits underwent unilateral 11-mm craniotomy within 2 mm of the coronal and sagittal sutures. Rabbits' calvarial defects were repaired by 1 of 2 interventions: 3DPBC scaffolds coated with 1000 mM dipyridamole (n = 14) or autogenous calvarial bone graft (n = 8). Six rabbits from the 3DPBC scaffold group were sacrificed at 8 weeks. The remaining rabbits (n = 8 each group) were observed until craniofacial growth was completed (6 months) and then euthanized. Bone regeneration, scaffold degradation, and cranial suture patency were analyzed in Amira software using reconstructed microcomputed tomography (muCT) images. Cranial growth was assessed by comparing bilateral cephalometric measurements based on muCT images. Bone growth and suture patency were qualitatively evaluated through histologic analysis.
Result(s): After 6 months of healing, animals with defects repaired with 3DPBC scaffolds regenerated an average of 53.9% +/- 3.6% (mean +/- SEM) bone, compared to 53.5% +/- 3.6% in defects repaired with bone graft (P = .95). Unoperated calvarial bone porosity was 49.4%+/-2.0%. Scaffolds showed significant degradation at 6 months (15.1% +/-0.7%) compared to 8 weeks (23.2% +/- 0.9%; P<=.001). Comparative measurements of operated and unoperated sides showed no significant differences in asymmetry between scaffold and bone graft animals (P > .24). Analysis of histologic sections revealed well-vascularized, organized bone formation within scaffold interstices with no evidence of ectopic bone formation, excess inflammatory cells, or suture fusion.
Conclusion(s): Dipyridamole-coated 3D-printed bioceramic scaffolds bone regeneration is comparable to autogenous bone graft without showing signs of adverse events such as premature cranial suture fusion, or detrimental effects to facial growth. The scaffold demonstrates favorable absorption kinetics, highlighting the potential for this technology in pediatric bone tissue engineering

This paper is aimed to present a biomaterials perspective in implant therapy that fosters improved bone response and long-term biomechanical competence from surgical instrumentation to final prosthetic rehabilitation. Strategies to develop implant surface texturing will be presented and their role as an ad hoc treatment discussed in light of the interplay between surgical instrumentation and implant macrogeometric configuration. Evidence from human retrieved implants in service for several years and from in vivo studies will be used to show how the interplay between surgical instrumentation and implant macrogeometry design affect osseointegration healing pathways, and bone morphologic and long-term mechanical properties. Also, the planning of implant-supported prosthetic rehabilitations targeted at long-term performance will be appraised from a standpoint where personal preferences (eg, cementing or screwing a prosthesis) can very often fail to deliver the best patient care. Lastly, the acknowledgement that every rehabilitation will have its strength degraded over time once in function will be highlighted, since the potential occurrence of even minor failures is rarely presented to patients prior to treatment.