Faculty Bibliography

OBJECTIVE: The purpose of this study is to evaluate the effects of saliva contamination on microtensile bond strength (microTBS) between resin interfaces and to determine which decontamination methods best re-established the original resin-resin bond strength. MATERIALS AND METHODS: Ninety-six light-cured resin composite cylinders of Z-250, Renew, Clearfil APX, and Pertac II were randomly divided into six groups. For each material, one group of specimens was not contaminated, serving as the control. For the other specimens, the top surface of each block was treated with saliva that was slowly dried (Treatment 1); dried forcefully (Treatment 2); slowly dried, rinsed, and dried (Treatment 3); slowly dried, rinsed, dried, and bonded with Single Bond, One-Step, Clearfil SE Bond, or Prompt L-Pop (Treatment 4); or slowly dried, but not rinsed, and bonded using the same adhesives (Treatment 5). Two 2-mm increments of resin composite were applied and light-cured. After 24 h, the assemblies were trimmed for microtensile bond testing and were loaded to failure at 1 mm/min. Data were analyzed using two-way and one-way ANOVA and Fisher's PLSD (p<0.05). RESULTS: Control values ranged from 45.1 MPa for Pertac II to 71.5 MPa for APX. Treatment 1 caused significant reduction in resin-resin bond strength for all materials tested but for two of the materials in treatment 2. Pertac II was the only material that did not show a statistical difference from control group for treatment 3. Treatment 4 re-established the control values for Z-250 and Renew and treatment 5 was the only one to show no statistical difference for all materials tested. SEM observation revealed a smooth surface in treatment 1, but treatment 3 showed a few craters. Treatment 4 and 5 showed a mixture of cohesive failure in the composite and adhesive. SIGNIFICANCE: The most reliable method for decontaminating saliva from resin surfaces involves the application of adhesives.

OBJECTIVE: Incremental placement and curing of resin composites has been recommended. However, this requires longer operating time, and therefore, increased risk of contamination. The purpose of this study was to evaluate the effects of blood contamination on microtensile bond strengths (microTBS) between resin interfaces and to determine the best decontamination method to re-establish the original resin-resin bond strength. MATERIALS: The top surfaces of 64, 4-mm composite blocks (Z-250, Renew, APX, Pertac II) were untreated as the control, or were treated as follows: blood applied and dried on the surface (Treatment 1), blood applied, rinsed, dried (Treatment 2), blood applied, rinsed, and an adhesive applied (Single Bond, One-Step, Clearfil SE, Prompt L-Pop) (Treatment 3). Fresh composite was applied and light-cured in 2-mm increments. After 24 h storage in water, the specimens were sectioned into 0.7-mm thick slabs, trimmed to a cross-sectional area of 1 mm(2), and loaded to failure at a crosshead speed of 1 mm/min using an Instron universal testing machine. Data were analyzed using two-way ANOVA and Fisher's PLSD test (p<0.05). RESULTS: Control values ranged from 45.1 MPa for Pertac II to 71.5 MPa for APX. Untreated blood contamination resulted in resin-resin bond strengths of only 1.0-13.1 MPa. Rinsing raised bond strengths to over 40 MPa for each material. Use of an adhesive further increased bond strengths except for Pertac II. SIGNIFICANCE: Rinsing blood from contaminated surfaces increases the resin-resin bond strength significantly and the application of an appropriate adhesive increases the bond strength to control levels.

AIM: To assess the treatment results up to 1 year after endodontic treatment of apical periodontitis using a silicone-based sealer in comparison with Grossman's sealer, and to compare the results at 3 months after treatment with the 12-month follow-up to assess the prognostic value of a 3-month control. METHODOLOGY: A total of 199 teeth were treated at three centres. The sealer was randomly chosen at the time of filling. Treatment results were evaluated clinically and radiographically 3 and 12 months after root-canal filling. The periapical status was evaluated using the periapical index (PAI). RESULTS AND CONCLUSIONS: Average PAI scores decreased from 3.43 at start to 2.21 at 12 months for Grossman's sealer and from 3.40 to 2.26 for the silicon-based material. No significant difference between the groups at start or any of the follow ups was seen. The 3-month control was adequate in establishing significant healing in both groups. The improvement of the periapical condition continued at the 12-month examination.

OBJECTIVE: To determine the incidence of concussion during the 2001 Division I-A college football season through utilization of the Internet. DESIGN: Prospective Internet survey. SETTING: Internet Web site. PARTICIPANTS: Head athletic trainers from Division I-A collegiate football programs. MAIN OUTCOME MEASURES: During the 2001-2002 football season, head athletic trainers from 87 Division I-A football programs agreed to use an Internet Web site to submit weekly data on the number of athlete exposures and concussions. RESULTS: A total of 373 concussions were reported over the course of a season in both practices and games combined. Of these concussions, 256 (68.6%) occurred during games, and 117 (31.4%) occurred during practice. The injury rate per 1,000 athletic exposures was 5.56 in games and 0.25 in practices. There were 230 grade 1 (61.7%), 134 grade 2 (35.9%), and 9 grade 3 (2.4%) concussions reported. There was a significant (p < 0.01) difference found between the total concussion injury rate and game concussion injury rate when comparing the Internet and the NCAA injury data collection methods. CONCLUSIONS: The results of this study suggest an underreporting of concussions using the NCAA Injury Surveillance System and demonstrate that the Internet is a simple and effective tool for data collection.